Announced 13-December-2016 by @RogersDave http://communityforums.rogers.com/t5/forums/forumtopicpage/board-id/Getting_connected/message-id/379...
Credit to @Hybrid_Noodle
Hitron website: http://www.hitron-americas.com/product/coda-4582/
60W Power Supply built into unit
Pictures of Hardware Version 1A:
You are correct, the modem is running in DOCSIS 3.0 mode at the present time. If there are enough CODA-4582 modems connected to your CMTS at some point, Rogers will be able to enable DOCSIS 3.1 downstream in which case the downstream LED will show purple apparently. DOCSIS 3.1 upstream is still under construction, as they say.
I hope all Rogers footprint will be on DOCSIS 3.1 by the end of 2017..
I think it'll be much, much, much sooner than that...
It seems that they've already conducted an extensive email campaign to get 500/gigabit users to swap their modems for the 4582; as @RogersDave explained it, getting enough of those folks away from D3.0 hardware is the prerequisite to reallocating capacity to D3.1...
What is considered the norm in terms of power cycling the CODA modem? Should one do this every 2 weeks or longer?
Back when I had my own router and ran DD-WRT I never power cycled it and the unit worked just fine. On some Belkin routers I have setup they have a feature called "Self Healing" which essentially schedules a reboot once a week.
What do you guys suggest?
My problem with this new modem is that it looses connection every 3-4 hours. I can ping websites but i cannot surf the web or do anything else. I have to reboot it every time and it's becoming very unpractical. I am thinking of switching to another operator. Any suggestions?
I am on firmware 184.108.40.206
error i get is:
84020200 warning Lost MDD Timeout;CM-MAC= ;CMTS-MAC= ;CM-QOS=1.1;CM-VER=3.1;
To power cycle the CODA modem or not? An interesting question. I didn't touch the CGN3ACSMR and it ran without any issues. I'm assuming the same here unless I see poor performance over several days, weeks, or months. I suspect that new firmware versions will result in power cycling or factory resets in the near future, so, for now, its a moot question I think.
@Eusquesio can you log into the modem, navigate to the STATUS .... DOCSIS WAN page, copy the downstream and upstream tables and paste them into a post. The copy and paste process will paste in the text contents of the tables, so you don't have to use a screen capture. Please copy and paste the two tables only, and none of the info above the downstream table. Those are the modem's signal levels which might show why you're experiencing problems.
Port ID Frequency (MHz) Modulation Signal strength (dBmV) Channel ID Signal noise ratio (dB)
1 591000000 256QAM 2.700 7 40.366
2 567000000 256QAM 2.500 3 38.983
3 573000000 256QAM 2.700 4 40.946
4 579000000 256QAM 2.500 5 40.366
5 585000000 256QAM 2.300 6 38.983
6 561000000 256QAM 1.600 2 38.983
7 597000000 256QAM 2.400 8 38.983
8 603000000 256QAM 2.300 9 38.983
9 609000000 256QAM 1.500 10 38.983
10 615000000 256QAM 1.500 11 38.983
11 621000000 256QAM 1.700 12 40.366
12 633000000 256QAM 1.400 13 38.983
13 639000000 256QAM 1.100 14 38.983
14 645000000 256QAM 1.200 15 40.366
15 651000000 256QAM 1.300 16 40.366
16 657000000 256QAM 1.400 17 40.366
17 663000000 256QAM 1.200 18 40.366
18 669000000 256QAM 1.100 19 38.983
19 675000000 256QAM 0.400 20 38.983
20 681000000 256QAM 0.400 21 38.605
21 687000000 256QAM 1.000 22 38.605
22 693000000 256QAM 0.600 23 38.983
23 699000000 256QAM 1.600 24 38.983
24 705000000 256QAM 2.200 25 38.983
25 711000000 256QAM 2.400 26 38.983
26 717000000 256QAM 2.700 27 38.983
27 723000000 256QAM 2.900 28 38.983
28 825000000 256QAM 1.100 29 38.983
29 831000000 256QAM 2.100 30 38.605
30 837000000 256QAM 1.500 31 38.983
31 843000000 256QAM 1.600 32 38.605
32 555000000 256QAM 1.600 1 38.605
OFDM Downstream Overview
Receiver FFT type Subcarr 0 Frequency(MHz) PLC locked NCP locked MDC1 locked PLC power(dBmv)
0 4K 275600000 YES YES YES 0.900002
1 NA NA NO NO NO NA
Port ID Frequency (MHz) Modulation Signal strength (dBmV) Channel ID Bandwidth
1 30596000 ATDMA - 64QAM 30.750 1 6400000
2 38595746 ATDMA - 64QAM 33.750 3 3200000
3 23700000 ATDMA - 64QAM 30.500 2 6400000
Channel Index State lin Digital Att Digital Att BW (sc's*fft) Report Power Report Power1_6 FFT Size
0 DISABLED 0.5000 0.0000 0.0000 -inf -1.0000 4K
1 DISABLED 0.5000 0.0000 0.0000 -inf -1.0000 4K
@Eusquesio you're signal levels look ok, but one interesting point is that there is only one OFDM Downstream channel running. I thought that there should be two OFDM channels running so that requires some checking. That indicates that the modem is running in DOCSIS 3.1 mode. The downstream LED at the front of the modem should be purple instead of blue. @RogersDave will have to have a look at this single channel situation and let us know if this is correct or not. You could try a factory reset to see if that turns on the other channel and if that fails simply swap the modem at the nearest Rogers store. That could be the fastest way to resolve this and it would be interesting to see if that resulted in both OFDM channels running.
You could also wait for Dave to have a look at your modem to see if there is some issue with the modem or the CMTS. Dave will need your modem's MAC address which is found in the modem's STATUS page. That page comes up when you log into the modem.
To send the MAC address to Dave, click on his name (link) @RogersDave to navigate to his public page. Select the right hand link to "Send this user a private message" That will take you to the message composition page which is already addressed. Fill in a title and in the details add your modem's MAC address and a quick explanation of what you're experiencing and indicate that there is only one OFDM channel running. Dave probably won't get back to you until Tuesday or Wednesday. Is Monday a holiday? Not sure.
Fwiw, in DOCSIS 3.1 mode the modem should be using the OFDM channels and it should be very fast on the downstream side, but I'm not sure of whether or not both OFDM channels are required.
@Big8D no, thats not a problem. In order to run DOCSIS 3.1, a certain percentage of the users connected to any given CMTS require the CODA-4582. At or above that threshold %, DOCSIS 3.1, which uses OFDM can be enabled on the CMTS. There is a bandwidth tradeoff as the freqency spectrum allocated to DOCSIS 3.1 will become exclusive to DOCSIS 3.1. @RogersDave can correct me here if I'm wrong. The remaining frequency spectrum will remain as is for DOCSIS 3.0 operation.
So, for now, your modem remains in DOCSIS 3.0 mode, which isn't a problem.
Please let me know if the swap manages to bring up both OFDM channels. If not, I would wonder if there is an issue with the CMTS to which your modem is connected.
Maybe I'm missing something (I'm in a still-3.0 area), but I thought the initial D3.1 deployment was only one OFDM channel, with another to come later as D3.0 capacity gets reallocated...
@RogersDave can you clarify? Has anybody observed two OFDM channels?