Rogers Hitron CODA-4582 Hardware

Need Help?

That's what we're here for! The goal of the Rogers Community is to help you find answers on everything Rogers. Can't find what you're looking for? Just ask!
cancel
Showing results for 
Search instead for 
Did you mean: 
Reply
Highlighted
I Plan to Stick Around
Posts: 11

Re: Rogers Hitron CODA-4582 Hardware

@Datalink u r correct, there is a difference of approx 100Mbps
Resident Expert
Resident Expert
Posts: 6,050

Re: Rogers Hitron CODA-4582 Hardware

The modem was running in Bridge mode,correct ?  If not, with the modem in Gateway mode and the router running in full router mode, you would have a double NAT situation running, which could cause slower data rates thru the router.

 

With the modem in Bridge mode and the router in full router mode, that gives you an idea of what the maximum throughput is for the router.  The nex question is what to purchase as a replacement?

 

What internet plan are you on?

 

Edit:  Just to point out, you can run two routers off of the modem when the modem is in Bridge mode.  In that configuration each will receive an IPV4 and IPV6 address of their own.  For the time being, the modem will supply two IPV4 addresses.  There is no limit on the IPV6 addresses apparently.  So, if you had some purpose to run a second slower network in addition a faster network with the new router, you could do that.  The only caveat to that is the security problems that arise with older routers.  You would have to ensure that the router is kept up to date, at least to the point in time where the manufacturer stops providing updates, after which, it would be time to retire the router or possibly load DD-WRT if that firmware supports your router.



I've Been Here Awhile
Posts: 3

Re: Rogers Hitron CODA-4582 Hardware

Got .24 firmware yesterday and my area is alread docsis 3.1 Didn't notice any speed increases, my max download is still roughly 850 mbs and upload roughly 54 mbs.

This is in Pickering

I Plan to Stick Around
Posts: 82

Re: Rogers Hitron CODA-4582 Hardware


@User9425 wrote:

Got .24 firmware yesterday and my area is alread docsis 3.1 Didn't notice any speed increases, my max download is still roughly 850 mbs and upload roughly 54 mbs.

This is in Pickering


Wow....I would be ecstatic with those speeds. My area in Scarborough (Lawrence/Meadovale) is 3.1 enabled and I also received the .24 yesterday but in my case it did not make any difference. I received a message saying that my Node was rebuild (although don't know what that means)....but speeds measured using various sources are still far below my 1Gbps Plan.  

Indeed ALL 4 ports on the CODA are active when in bridge mode. Test results now at noon in Bridge mode, port 1 Down: 311 Up:32, Lat:8 Jit: 1 In Native mode using Port 3 connected to Win Laptop. Down: 253 Up: 23 Lat: 9 Jit: 12 (Looks like port 1 is getting priority and faster)

My signal strength on various channels are not optimum, although the Intek strung a new cable to the house.  Appreciate any suggestions:

 

Downstream Overview

Port ID

Frequency (MHz)

Modulation

Signal strength (dBmV)

Channel ID

Signal noise ratio (dB)

1

591000000

256QAM

0.800

7

36.610

2

567000000

256QAM

-0.600

3

36.387

3

573000000

256QAM

0.000

4

36.610

4

579000000

256QAM

-0.500

5

36.610

5

585000000

256QAM

-0.100

6

36.387

6

561000000

256QAM

-2.000

2

36.387

7

597000000

256QAM

1.800

8

37.356

8

603000000

256QAM

1.500

9

37.356

9

609000000

256QAM

1.000

10

36.610

10

615000000

256QAM

2.300

11

36.610

11

621000000

256QAM

3.000

12

37.356

12

633000000

256QAM

2.900

13

36.387

13

639000000

256QAM

3.700

14

37.356

14

645000000

256QAM

3.500

15

37.356

15

651000000

256QAM

3.700

16

37.356

16

657000000

256QAM

3.200

17

36.610

17

663000000

256QAM

2.900

18

36.610

18

669000000

256QAM

2.800

19

36.610

19

675000000

256QAM

2.800

20

36.610

20

681000000

256QAM

2.300

21

36.610

21

687000000

256QAM

1.500

22

36.610

22

693000000

256QAM

0.600

23

36.387

23

699000000

256QAM

0.800

24

36.610

24

705000000

256QAM

0.000

25

36.387

25

711000000

256QAM

-1.900

26

35.780

26

717000000

256QAM

-2.200

27

35.595

27

723000000

256QAM

-1.800

28

35.595

28

825000000

256QAM

-6.800

29

33.957

29

831000000

256QAM

-6.800

30

33.834

30

837000000

256QAM

-6.300

31

34.484

31

843000000

256QAM

-6.600

32

34.346

32

555000000

256QAM

-2.000

1

35.780

OFDM Downstream Overview

Receiver

FFT type

Subcarr 0 Frequency(MHz)

PLC locked

NCP locked

MDC1 locked

PLC power(dBmv)

0

4K

275600000

YES

YES

YES

0.700001

1

NA

NA

NO

NO

NO

NA

Upstream Overview

Port ID

Frequency (MHz)

Modulation

Signal strength (dBmV)

Channel ID

Bandwidth

1

38596000

ATDMA - 64QAM

36.250

3

3200000

2

30596000

ATDMA - 64QAM

33.250

1

6400000

3

23700000

ATDMA - 64QAM

32.750

2

6400000

OFDM/OFDMA Overview

 

Channel Index

State

lin Digital Att

Digital Att

BW (sc's*fft)

Report Power

Report Power1_6

FFT Size

0

DISABLED

0.5000

0.0000

0.0000

-inf

-1.0000

4K

1

DISABLED

0.5000

0.0000

0.0000

-inf

-1.0000

4K

 

DOCSIS event logs:

No.

Time

Type

Priority

Event

1

01/01/1970 00:01:05

82000200

critical

No Ranging Response received - T3 time-out;CM-MAC=xx:xx:xx:x:xx:;CMTS-MAC=xx:xx:xx:x:xx;CM-QOS=1.1;CM-VER=3.1;

2

02/16/2017 22:51:28

90000000

warning

MIMO Event MIMO: Stored MIMO=1 post cfg file MIMO=-1;CM-MAC=xx:xx:xx:x:xxCMTS-MAC=xx:xx:xx:x:xx;CM-QOS=1.1;CM-VER=3.1;

3

02/17/2017 05:35:49

84000500

critical

SYNC Timing Synchronization failure - Loss of Sync;CM-MAC=xx:xx:xx:x:xx;CMTS-MAC=xx:xx:xx:x:xx;CM-QOS=1.1;CM-VER=3.1;

I Plan to Stick Around
Posts: 98

Re: Rogers Hitron CODA-4582 Hardware

For those people who didn't notice that the .23 f/w that was pushed out has the ability to review all the ports on the back of the modem and you can enable them or disable them with a toggle switch and they all mention that they 1Gb ports enabled by default.

I Plan to Stick Around
Posts: 85

Re: Rogers Hitron CODA-4582 Hardware

Anyone here from Malvern area or nearby?

 

I had a tech visit me today. He told me he had just visited someone in that area with similar issue as mine (speed degradation issue).

I'm Here A Lot
Posts: 6

Re: Rogers Hitron CODA-4582 Hardware

Hi Dave , Do we have any updates on this ? I still could not view any updates on the firmware 

 

 

Regards, 

Savio 

I'm Here A Lot
Posts: 5

Re: Rogers Hitron CODA-4582 Hardware

Today around 1pm. 24 was pushed to my modem. I noticed as both up and down links were flashing and then it rebooted... I'm getting stable 920mbps down and 50 mbps up. Brampton main and Steeles area. On D3.1
I Plan to Stick Around
Posts: 11

Re: Rogers Hitron CODA-4582 Hardware

Thanks. I hope so. Overnight I was pushed from the .13 to .19 I saw but didn't have time to test this morning.

Hopefully by the time I get home from work I'll have the latest .24 and test it out.
I Plan to Stick Around
Posts: 19

Re: Rogers Hitron CODA-4582 Hardware

On the 16th I had a software download init via nms but I am still at .23, didn't get the .24. What can I do to get the .24? @RogersDave