@JohnBeaudin wrote:
Curious about what will be .27 patch notes vs .26 that I am curently testing?
John,
As far as I’m aware, changes between .26 and .27 are not customer facing or performance related. It is all backend related so nothing exciting here.
If you haven't swapped the modem yet, ensure that you swap both the modem and power brick. At the store, check the model type at the back of the modem. Look for a CGN3ACSMR. The store staff might not appreciate that, but, it is what it is.
If you manage to bring home a CGN3ACSMR, that modem will be updated automatically within 48 to 72 hours of going online. It will update to 4.5.8.22. If you bring home a CGN3ACR, or CGN3AMR, you will have to request the update to 4.5.8.22. If you bring home a gigabit CGNM-3552, (that would be my preference if there is no additional cost) you will also have to request the update.
To request the update, have a look at message # 471 (top post) on the following page for instructions on requesting the trial version, 4.5.8.22.
When you are sending the private message as indicated in that post, also log into your modem and copy the HFC MAC address and modem Serial number and paste that into the message. The HFC MAC Address and modem Serial Number can be found on the STATUS page that is displayed when you log into the modem. The Cable Modem MAC Address and S/N can also be found on the back of the modem.
@Mythen, can you run a speedtest using the Toronto Rogers speedtest server as indicated below. Please let me know what the results are and what version Firmware is currently loaded. I suspect that it's .19. After .22 is loaded, please rerun the test and post those results as well. Other users have reported slow upload results with the CGNM-3552, so, I'm wondering how your results will turn out..
From @RogersDave: "....on Speedtest.net, Rogers has servers. They simply don’t show up in the list for Toronto because there are too many servers. It is however possible to select this server by clicking in the upper right corner on “Settings” then in the lower right Preferred Server: “Mississauga, ON [CA] – Rogers” or “Toronto, ON [CA] – Rogers”. This should give more accurate results of the last mile. These servers are actually way better than the old speedcheck.rogers.com as they have 40 Gbps connections to them. After setting a preferred server, the main speedtest.net interface will provide 2 options: “Begin test – recommended servers” and “Begin test – preferred server”."
Your saved server will be the preferred option at this point.
Learn something new all the time as they say 🙂
Hmm, ok, in that case try the Montreal Rogers server. What I'm looking for are any signs of a drop in the upload speeds when you go from .21 to .22. I don't expect any, but would like to see how the speedtest numbers turn out.
Your posted test results don't look to bad at all. You should see the same results for a Mississauga test with .22 loaded.
On the speedtest site, select "Settings" from the top menu, and then in the lower right hand side on the next page, there is a drop down menu for "Preferred Server" which lists numerous servers from around the world. There is a Rogers server in Montreal and also in Moncton. The Moncton server might be the closest Rogers server for you. I'd compare the results for Montreal and Moncton, just for the heck of it.
@Breadwinka I've seen a few posts that indicate the same. Don't know when the policy changed. Maybe its a matter of what stock is available in the store at the time??
@IwasDerp, can you consider trying the following as an experiment to see if it resolves the low upload rates. I hate to ask anyone to go thru all of this, but I would like to see if this might resolve the situation with new installs going wrong.
1. Run a factory reset of the modem by either holding down the recessed reset button at the back of the modem for 30 seconds and releasing it. Or, by using the Factory Reset function located in the modem's ADMIN .... DEVICE RESET page.
2. When the modem reset is complete, run the setup required to enable you to log into the modem and kick it back into Bridge mode.
3. When the reboot back into Bridge mode is complete, run a factory reset of the router. Sorry, but this will require you to reset the router parameters.
4. When the router reboot and reset is complete, with the connected pc or laptop, bring up a command prompt with admin privileges and enter;'
ipconfig/release
ipconfig/flushdns
ipconfig/renew
When that is all done and you're up and running run a speedtest using the www.speedtest.net Toronto Beanfield server or the Rogers Toronto or Mississauga server. To access the Rogers Toronto server,
on Speedtest.net, select "Settings" from the upper menu list. Then on the next page, in the lower right Preferred Server: “Toronto, ON [CA] – Rogers”. Save the setting. After setting a preferred server, selecting "Take a speedtest" will take you back to the main speedtest.net interface which will provide 2 options: “Begin test – recommended servers” and “Begin test – preferred server”."
Your saved server will be the preferred option at this point.
Let me know how this all works out.
The purpose of resetting everything from scratch is to:
1. Ensure that the modem really is updated and not just loaded without completing the update.
2. Wipe out any previous DNS settings from your router which point to the previous ISP servers.
3. Wipe out any IP address data and DNS data from your pc or laptop that point to the previous ISP servers.
Whenever you switch ISPs, its usually a good idea to reset the router from scratch to remove data that is no longer in effect and to flush the DNS cache and any old IP data from the pc or laptop.
Edit;
If, when this is all said and done, and you notice service dropouts, try the following, but, only do one at a time:
1. Disable IPV6 in the router if you don't do so already. Then reboot the router. When the router reboot is complete, once again bring up a command prompt in the connected pc or laptop and run the same sequence to flush any IPV6 data:
ipconfig/release
ipconfig/flushdns
ipconfig/renew
2. If that has no effect, after watching for further failures, set a DNS address in your router if you don't do that already. If you normally leave the DNS fields empty in the router, then the router and any connected device will use the Rogers router. So, enter DNS server addresses in the primary and secondary address fields so that you will no longer be using the Rogers DNS. Here are a couple you could use:
OpenDNS is 208.67.222.222 and 208.67.220.220
Google is 8.8.8.8 and 8.8.4.4
When that is done and saved, reboot the router, and once again bring up a command prompt in the connected pc or laptop and run the same sequence to flush the Rogers DNS data:
ipconfig/release
ipconfig/flushdns
ipconfig/renew
Keep the IPV6 disabled in the router for now, looking for any further failures. If you don't see any failure after a few days, consider enabling IPV6 and watch for any failures after that point.
What router model do you have?
At the present time 4.5.8.22 is it. The next trial version has only been released to a very limited group pending further changes to the firmware before it's released to a larger test group. That release might come this week. Just speculating.
-
915192 views
-
669 Likes
-
-
