*** This post was last edited May 2, 2017 ***
Good morning Community,
As I mentioned in a post two days ago, we have received the next firmware 2.0.10.20 from Hitron. We are currently running initial testing on this version and will push it out to participants in the firmware trial program as soon as it passes initial testing.
However, while running these tests, we discovered abnormal behavior with ICMP and are awaiting feedback from Hitron today to asses how this will be addressed. As soon as I this is confirmed, I’ll update the change log with the correct version information and start pushing it out.
In parallel, we are still working on the following high priority items. In some cases below, I requested affected customers to reach out to me via private message. If you do so, please include your modem MAC address in the subject line (even if we exchange messages daily) as there are a lot of you reaching out to me daily 🙂
UDP Packet Loss
The investigation for what has been reported as UDP packet loss is still ongoing. We have deployed a probe at one fellow forum member on both a CODA-4582 and a CGNM-3552 to collect additional data. We are actively working with Hitron and Intel on the results observed.
Based on what we know so far, in most instances UDP packet loss is coupled with higher uplink usage in the area. Although the impact is noticeable in specific logs (League of Legends), the root cause for the perceivable impact (while playing) is likely related to bufferbloat (see next issue).
Bufferbloat
When comparing the performance of a CODA-4582 to a CGNM-3552 in the same network conditions, the CODA-4582 consistently reports higher bufferbloat when tested on DSLReports.
Update April 12: The solution for this problem will come in two folds. It will require a change in software which will possibly be included in 2.0.10.27 but more likely in 2.0.10.28 and a change in network configuration.
The network configuration change is not compatible with the current firmware so this change will only come after a vast majority of the modems are running the new code. We are however looking at a way to make the change only for specific modems to support testing in the community.
Update April 22: This problem seems resolved in firmware 2.0.10.27
5 GHz WiFi Low range for channels 36 to 48
Lower WiFi channels on the modem have a much smaller range. This is due in part to the limit imposed by Industry Canada to maximum transmit power.
Furthermore, the current automatic channel selection (auto mode) tends to select the lower channels when in similar load conditions.
Workaround: manually select higher channels (149-153-157-161)
Update April 22: The channel selection algorithm has been improved in firmware 2.0.10.27
Loss of OFDM Channel Lock
Under some RF conditions, the modem fails to lock properly on the OFDM channel. This typically result in variable performance.
Update April 12: This problem is resolved in 2.0.10.26T2
List of connected device does not get fully populated
This is a known issue that has been tracked since firmware 2.0.10.13. We are making improvements at every firmware but it is not a perfect system.
The situation is worst after a reboot or firmware upgrade as the list gets reset and must be repopulated as devices renew their DHCP lease.
NAT Loopback not working for wired clients
When setting up port forwarding to an internal server, it is possible for a client on WiFi to reach the server using the external IP/port. If the client is on a wired interface, it doesn't work.
Update April 12: This problem is resolved in 2.0.10.26T2 (not confirmed)
LAN Counters not working
Some customers reported that LAN counters (especially in bridge mode) are reporting inaccurate values.
This problem has been reported to Hitron for investigation.
Unexpected modem reboot
Some customers reported their modem reboots unexpectedly. We have also seen this behavior in our lab.
Update April 12: This problem is resolved in 2.0.10.26T2
Missing SC-QAM Channels
After a reboot, some modems are missing SC-QAM channels. A fix has been implemented in 2.0.10.26T2 to address this behavior but it has not corrected all scenarios.
Investigation continues with Hitron.
WiFi Survey
The WiFi Survey functionality in firmware 2.0.10.26T2 (and possibly before) reports incorrect SSID names.
Guest Network
When connecting to the Guest Network, an error message is displayed "only allow DHCP client to use this wireless". This has been reported in firmware 2.0.10.26T2.
Update April 22: This issue has been resolved in firmware 2.0.10.27
Update May 2: It seems this issue is not fully resolved and still experienced by some users
Future Planned Improvements
The following are items that we are working on in parallel of the above.
- Improvement in WiFi speeds
- Improvement in latency / bufferbloat
Dave
*Edited Labels*
Hey @soundwave80!
Any form of latency can be incredibly trying to deal with to say the least. I'll be happy to assist and identify for you if the issue is network related. Can you PM me your MAC address? Also are you using your own router, and if so have you tested the connection wired directly to the modem with a single device?
Thanks!
@kermit1 this is an ongoing problem thats been around for seemingly forever. There are two firmware versions in use, V2.0.10.36T6 and V7.1.1.30. The problem that you're referring to is definitely in 2.0.10.36T6. V7.1.1.30 is fairly new and is supposed to be replaced by the end of the month. I don't know if the same problem as been carried over to 7.1.1.30 and later versions.
To find your firmware version, log into the modem and check the Software Version (firmware version) that is shown on the STATUS page. That page is displayed when you log into the modem. Please let me know what version you have loaded.
@kermit1 as far as 2.0.10.36T6 is concerned, nope, sorry 😞 This is a firmware issue that only Intel and Hitron can fix. I can probably have a look at 7.1.1.30 at some point to see if the same problem has been dragged into this version as well, or if Intel and Hitron has finally fixed the problem. Its difficult to test this as my 4582 is running in Bridge mode, so I'll have to find a point in time when no one else is using the internet so that I can swap over to Gateway mode. Definitely not easy to do that these days. Ask this again over the next couple of weeks, just to make sure that I don't forget about this.
Hi @alduk,
Welcome to the Community!
Thank you for listing the troubleshooting steps you've tried so far. Is your modem in bridge mode? Where is the Ethernet cable plugged into the Orbi router? Did you try a different Ethernet cable? Aside from the Orbi Router, do you also have an Orbi Satellite?
Looking forward to hearing from you!
RogersZia
- last edited on by
RogersMoin
Thanks so much for the additional information @alduk,
If the connection is working direct to the modem without the Orbi connected, then yeah it would be an Orbi connectivity concern. Have you gone through any of Netgear's troubleshooting steps here? I'm afraid our ability to assist outside of Rogers hardware specific concerns is rather limited.
Perhaps if other's within the community have the Orbi they can weigh in.
-
475658 views
-
295 Likes
-
-
