05-13-2016 08:55 AM - last edited on 05-13-2016 09:04 AM by RogersMoin
Have yet to pick one up myself.. but will possibly try this week.
Its an RF remote, so it doesnt need line of sight.
This will be a great asset to people wanting to set up a home theatre, etc type of setup where the box may not be right infront of the TV itself.
Though.. the TV on/off part of it (or any other paired devices) will still be done via IR and not RF.
Solved! Solved! Go to Solution.
03-30-2018 07:04 PM - last edited on 03-30-2018 07:33 PM by RogersMoin
@bscrivens : Here's the link for Chat, note the times:
03-31-2018 09:15 PM
Sorry, when I said "manufacturer's site"I meant the remote, not the sound bar.
04-01-2018 10:16 AM
Alright well I talked to a Rogers representative and he basically said it probably isn't supported, meanwhile I've seen others say they have had success pairing theirs on here. I don't know what gives.
05-16-2018 11:51 AM
05-16-2018 11:57 AM
My other remote was paired. new RF remote doesn't know how to!?
05-16-2018 12:28 PM
I would like to pair the RF remote to turn on/off the Sat/TV/sound system on the same time? How are we doing that?
Go to the following website for information on the remote.
Programme in the appropriate code for your various devices. Then programme the "Watch Cable" functionality to turn on/off those devices, assuming you've found working codes for those devices first.
07-01-2018 09:52 PM
I also find that the 2125 remote seems to lose the programing for cable. Any time I want to change a channel or move the volume up or down I have to press the cable button for the remote to become responsive. Sometimes I have to press the cable button a few times before it becomes responsive. Definitely not a good remote.
Rogers we expect better from you.
07-02-2018 09:53 AM
@LoopyWhen you go to change channels and it "does not respond", which of the device buttons lights up instead of CABLE? My 2125 always stays on CABLE. It's the old Atlas one that loses the cable function when one of the other device buttons gets pressed. I always make sure I press the CBL button on that one before using it to ensure my PVR and TV don't get out of phase. How long have you had this 2125 remote and when did it start doing that? You know you can take it to a Rogers store and they'll give you a new one.
07-03-2018 11:57 PM
Thank you for responding Old Yeller. The button seems to go back to the TV button. I then have to push the cable button some times several times to get it to stay there long enough to change the channel or pump up the volume. Maybe it's just me and technology. Not a good combination. Maybe I'll try and find a Rogers store and take it back because it's very annoying. Thanks again for your reply.
12-16-2018 09:51 PM - last edited on 12-16-2018 11:28 PM by RogersMoin
remote doesn't work on nextbox
For some reason the remote stopped working for the TV and the nextbox. I was able to reprogram the remote to control the TV, but can't find anything on resetting the control for the nextbox. i.e. can't change channels or view the guide or anything like that, but I can turn the TV on/off and control the volume no problem.
12-17-2018 11:56 AM
...can't change channels or view the guide or anything like that, but I can turn the TV on/off and control the volume no problem.
I assume you've pressed the "Cable" button at the top right of the remote to send signals to the box and not the TV? Does the Cable light flash when you press the buttons? If you call Rogers they should be able to provide you with a sequence of button presses to get the remote back to "factory (Rogers) settings". You can then reprogramme the TV portion if necessary.
Perhaps someone here will provide that information, but a call might be easiest, or use "Share a Concern" or Twitter or FB.
There's also the URC website that may have something:
12-19-2018 05:12 PM
Just picked up the RF Champion remote paired it with my Nextbox 3.0, works fine but not in RF mode, meaning line of sight needs to be there. I did the "pairing" holding setup + up arrow .. still nothing
So I either need an IR Extender cable or Harmony remote correct?
12-19-2018 05:16 PM - edited 12-19-2018 05:19 PM
@MikeDoba : Did you follow the complete instructions per post 3 of this thread?
Did you get the "confirmation"? It should work with the 9865. (I assume you have the 9865 PVR - model number on the front of the PVR)
12-19-2018 05:20 PM
Yes I followed the Pairing Mode instructions, the cable button flashes continually, 63 times I think I counted.. still not working in RF.
12-19-2018 05:23 PM
Try "unpairing" and then "repairing". It shouldn't require that many flashes. See instructions below:
Do you have the 9865 PVR?
12-19-2018 05:32 PM
yes I have the 9865 PVR.. I tried unpairing as per video instructions, the light blinks only one time.
I tried Pairing again, again something like 73 flashes lol.. obviously pairing not working, Im holding the remote directly in front of the receiver.
12-19-2018 06:16 PM - edited 12-19-2018 06:55 PM
Soo its not the Remote its my receiver I think. I have the same receiver upstairs, and managed to program both new remotes in RF mode and both remotes work! confirmed. Yet I cant set either remote downstairs to the exact same receiver as upstairs.. Weird.
12-19-2018 06:54 PM
UPDATE 3.0 - Super weird Keep up!
Since the upstairs receiver programmed successfully in RF I took it downstairs in exchange for the one down here. Once the receiver from downstairs was upstairs it too took the RF programming the first time. Yet it wouldn't do it when located in basement. So now both receivers work in RF mode .. Sweet
12-19-2018 07:05 PM - edited 12-19-2018 07:12 PM
Be aware, per the link in my previous post, that you should not use RF if you have more than one PVR since you might affect the one in the other room when you don't want to. Make sure that doesn't happen by "seeing" what happens to the "other" PVR when controlling the first PVR. Perhaps the "pairing" is unique and you won't affect the other one. I don't have this remote.
The reboots caused by moving the PVRs probably fixed any firmware issues allowing you to pair.
12-20-2018 07:23 AM
01-15-2019 07:59 PM - last edited on 01-15-2019 10:33 PM by RogersMaude
I have a brand new Rogers remote and I have to press any button 3 times before it works. Say I hit the guide button. The cable button flashes twice and nothing happens. Press it again quickly after and it works. Want to change a channel and press 5 and nothing happens. I wait and the cable button flashes twice. Then I have to input the number again. Very frustrating