@jsp563 you should also be able to call tech support to disable the SIP/ALG. Give that a go and let us know if you encounter any problems with tech support. This was a pay for service "disable" not so very long ago but that has changed and the first line techs should be able to do this now. By now the memo should have trickled down to the support techs.
Ok, when the tech supervisor disabled the Residential Gateway function, you should have seen the modem do a reboot into Bridge mode. Up until that point in time, in Gateway mode, you had a double NAT situation going unless you had the router set to Access Point mode. Now with the modem in Bridge mode, the router should be in full router mode.
You should restart the router now to allow it to pick up the correct IP address and obtain the necessary IPV6 address data so that the connected devices are given their own IPV6 address, if in fact you have IPV6 enabled in the router.
You should ensure that you have any port forwarding settings for the VOIP device set and that the SIP/ALG in the router is also disabled. If you have to set those, do another router reboot, and reboot the VOIP device as well.
The reboots/restarts of the modem and VOIP device should ensure that the router and VOIP device pick up the correct IP addresses and are operational. That should also solve the speed issue that you are having.
With the modem in Bridge mode, that disables the vast majority of the modems functions, so, items such as the SIP/ALG setting in the modem are no longer functional.
To log into the modem thru the router, use 192.168.100.1 as a web browser address. That will take you to the login page. If you wanted to reset the modem back into Gateway mode, you can use the recessed reset button at the modem. Hold that down for 30 seconds and the modem will reboot back into Gateway mode with its default settings. If you log into the modem, and enable the BASIC .... GATEWAY FUNCTION .... Residential Gateway Function, the modem will reboot into Gateway mode with all of its previous settings intact.
Please let us know if this resolves the VOIP and speed issue.
That usually works, but, not in all cases. Usually when that happens you have to specify a routing rule to allow access to that address. I don't think I've seen anyone with a TP-Link router have that problem before.
With the router set for Auto Detect or Dynamic IP, when you reboot it, it should pick up an IP address from the modem. That is normally 191.168.0.1 which I believe is the same as the default address of the router.
If you can't access the modem thru the router, you can simply connect a pc or laptp to one of the other modem ports. At this point you should only have the router connected. Plugging in another device such as a pc/laptop will work, at least at this point in time. The pc/laptop will pick up an IPV4 and IPV6 address. You can then log into the modem using 192.168.100.1 with the modem still in Bridge mode. So, that would allow you to check the cable signal levels if necessary or kick the modem back into Bridge mode if you wanted to.
The only caveat with that configuration is that the pc/laptop is relying on its own firewall for protection from outside probing. So, I advise anyone who does this to only run the configuration for as short a time as possible to carry out a test or log into the modem, and then retreat behind a router firewall, plugging the pc/laptop back into the router.
I'm assuming at this point that you have the modem running in Gateway mode again? Please confirm that.
And is the Vonage phone connected directly to the modem, or do you still have the router connected to the modem and the phone connected to the router?
Two things usually have to happen.
1. You normally have to set port forwarding rules so that the signaling and voice data go to the phone; and
2. You have to disable the SIP/ALG.
Before you set the port forwarding rules, you should use the DHCP reservation function to set a static IP address for the phone. So, with the phone connected, log into the modem and navigate to BASIC .... LAN setup. Ust the DHCP Reservation function to set a static IP address. You can use what the phone is using now, or set a different IP address. Thats your preference. When that is done and saved, reboot the modem by using the ADMIN .... DEVICE RESET .... Reboot function.
After the reboot is complete, you will need to log back in again and set the port forwarding rules as required by the specific model of Vonage Phone. There should be a list of ports on the phone support page that require forwarding. In the modem, navigate to BASIC .... PORT FORWARDING. Enable the function and add one rule for each port number. So, you're going to set a rule that uses the same port number, on the Public side and Private side of the modem, with the protocol as indicated on the Vonage phone support page. Point that toward the IP address that you have previously assigned to the phone. When that is all done and saved, reboot the modem again.
When the reboot is complete, with the ports set and SIP/ALG disabled, your phone should be operational.
If you have decided to use the router, then the modem should be in Bridge mode and the router should be in full router mode. Follow the same guidelines as above to set a static IP address for the phone and then assign the ports for forwarding. Same idea no matter if you use the modem in Gateway mode with a direct connection to the modem, or if you use the router, with all of your networked devices connected to the router.
When that is all said and done, navigate to ADMIN .... BACKUP. Use the backup function to create a backup settings file for the modem configuration somewhere on your pc. You need to do that as the modem will most likely dump the configuration if power to the modem is lost for any reason. If that's the case, you can log back into the modem, possibly after running a factory reset, browse to the backup file location and restore that file. After the restore is complete, reboot the modem. You should be back at square one in 5 minutes or less.
Let us know how this works out, or if you need further help.
Ok, take note of the DHCP Start and End Ip, as well as the MAC address and IP of the VOIP phone which should be shown on the bottom of the page in the connected devices list.
Select the DHCP reservation function. That will bring up a secondary panel that will let you assign a specific IP to the VOIP phone. I haven't looked at that panel for a while but it should contain an entry window or drop down menu to allow you to select the VOIP phone, probably by MAC address. Then you can either use the current IP address if you prefer, or choose another address as long as there is no conflict with another device at the present time. That will change the IP from a dynamic IP which can change whenever the modem reboots or the phone powers up again, to a static IP which will remain the same. At this point, with the data saved, reboot the modem and power cycle the phone (power off/power on). If you have assigned a different IP address, after the reboot and phone restart, the phone will or should have the IP address that you assigned.
Next is to assign the port forwarding rules to the assigned IP address. For each port number, you will have to create a rule. I think the modem asks for a rule name. Use something like phone 1, phone 2, phone 3, etc, etc until all of the ports are entered into their own separate rule. The Hitron modem won't let you assign port 80 from what I remember. Thats a common port but it shouldn't make any difference to the phone operation if that port isn't assigned. With the data saved, reboot the modem.
As far as the SIP/ALG setting is concerned, as long as the modem has power, that setting should be maintained. If the modem loses power it will drop the setting. What you can do, just to ensure that you don't lose the setting, create a backup file before you do the first reboot. Then make the next series of changes. Make another backup file, reboot. Do that all the way to the end. Every time you create a backup file, it will create one with a (1), (2) appended to the file name, so you know that the later files have the larger number at the end of the name.
If there was a problem and the SIP/ALG setting was lost, you can simply contact @CommunityHelps and have one of the mods disable it again.
That requirement to ask tech support or @CommunityHelps will go by the wayside on the next firmware update for the CGN3ACSMR and CGNM-3552 as it is included as a user selectable function. V4.5.8.27 is being distributed to the trial CGN3ACSMRs at the present time. I suspect that it shouldn't be very long before a decision is made to distribute that version network wide to all of the CGN3ACSMRs. If you look at the back of the modem, you will see the product sticker which indicates the model of the modem that you have.
@something1965, have a look at the English user manual for your router, which can be downloaded here:
http://support.dlink.ca/ProductInfo.aspx?m=DIR-878
Look at the SIP note contained on page 67, within the Firewall settings. You will have to ensure that the SIP is disabled in the router. If your modem is in Bridge mode, it will not interfere with the SIP/ALG function of devices connected thru a follow-on router.
With the CGN3, if you run the modem in Gateway mode, you will have to call tech support to disable the SIP/ALG. The later CGN3xxxx modems running later version firmware should have a SIP/ALG enable/disable function within the BASIC .... GATEWAY FUNCTION tab. That tab can only be accessed when the modem is running in Gateway mode. In Bridge mode the modem should act as a transparent bridge and once again you would have to disable the SIP/ALG in the connected router.
@hannajTO log into the modem and navigate to BASIC .... GATEWAY FUNCTION. If the firmware has been updated to include it, you should see a SIP ALG enable/disable function at the bottom of the list. While you're there, I'd also disable UPNP as well, unless you know that you want it for gaming purposes.
If the SIP/ALG is not on that page, then it will be time to contact tech support to disable it.
-
29315 views
-
6 Likes
-
-
