Dynex TV and programming remote

Need Help?

That's what we're here for! The goal of the Rogers Community is to help you find answers on everything Rogers. Can't find what you're looking for? Just ask!
cancel
Showing results for 
Search instead for 
Did you mean: 
Reply
Highlighted
I've Been Around
Posts: 1

Dynex TV and programming remote

Hello, we have a Dynex TV and the Digital box remote is programmed and turns the TV on and changes TV volume but it will not turn the TV off, it turns it off and right away it turn back on. How can we fix this. When we use the TV remote the TV works fine and turn on and off with out a problem. Any ideas of how I can fix this? Please do not answer with instructions on how to program my remote as I have exhausted those options. Thanks

 

 

 

***Edited labels***

Highlighted
Resident Expert
Resident Expert
Posts: 2,766

Re: Dynex TV and programming remote

you can always try a DIFFERENT code. i have problems with one code but when i try a different code the problems go away. hope this helps you better than telling you the instructions all over again, lmao.


Highlighted
I've Been Around
Posts: 1

Re: Dynex TV and programming remote

I have the exact same problem and have not figured out a solution.  It is rather annoying having to turn off the tv again after powering off the cable box. I also have a Dynex TV.

Highlighted
I've Been Around
Posts: 1

Re: Dynex TV and programming remote

Hi,

 

I have the same problem, (Dynex TV, rogers remote, turning off turns it back on). I found that if u cover the infrared right after the light goes out on tv, then ur safe. 🙂 alot of trouble to go thru.I have 2 other rogers remotes and they also do the same on the same TV.

 

"in the same wishing pool for a FIX"

 

-dricard

Highlighted
I've Been Around
Posts: 1

Re: Dynex TV and programming remote

Use the code 1463.

Highlighted
I've Been Around
Posts: 1

Re: Dynex TV and programming remote

The 1463 code didn't work for me

 

Highlighted
I've Been Around
Posts: 1

Re: Dynex TV and programming remote

Code 1463 worked for me, thanks

Highlighted
I've Been Here Awhile
Posts: 4

Re: Dynex TV and programming remote

http://www.urcsupport.com/images/uploaded_images/Atlas_OCAP_M1056.pdf

This is a link for the FULL REMOTE MANUAL

 

INCLUDED ARE SOME COMMON SECTIONS TURNING TV ON/OFF and programming MASTER POWER

 

You should be able to just do the first one and turn the tv and box off at the same time, (FOR THIS TO WORK THE REMOTE HAS TO BE IN CABLE MODE)

 

I suggest reseting the remote to factory settings first i've included those steps at the bottom of this thread,

 

Practice these steps they have to be done properly or it will not work 🙂

 

Programming Remote to turn off TV

  1. Aim the remote control to the TV and press TV once until the TV button flashes.
  2. Hold down setup until the TV light flashes twice.
  3. Enter the TV manufacturer code. in this case 1463 is the only known code for DYNEX
  4. Press power and the TV should turn off.

Master Power Programming to Sync Cable and TV

  1. Press cable once until cable light flashes.
  2. Hold down setup until the cable light flashes twice.
  3. Enter the code 995.
  4. Press power.
  5. Press cable.
  6. Press power.
  7. Press TV.
  8. Press power.
  9. Press cable.
  10. Hold down setup until the cable light flashes twice.
  11. Press cable.
  12. Press power.
  13. The cable box and TV will both power off.  The cable will go off first followed by a slight delay of the TV.

 

Resetting The Remote Control

  1. Press cable once until cable light flashes.
  2. Hold down setup until the cable light flashes twice.
  3. Enter the code 981 or 1877 or 0877 sometimes its one or the other
  4. Cable light will flash 4 times.
  5. Remote will reset to factory settings.
Highlighted
I've Been Here Awhile
Posts: 2

Re: Dynex TV and programming remote

seems like the Rogers universal control is sending 2X signals to turn OFF.  I don't know if this is actually what it's doing, but that's how it looks.

 

I have same problem described above, regardless of the Dynex code used (all of 1463, 0463, 0049) produce same results when programmed into Rogers remote control....

 

Turns Rogers Cable box ON and Dynex TV ON, no problem.

 

Turns Rogers Cable box OFF and Dynex TV OFF, then turns Dynex TV ON.

 

Result....Rogers remote control cannot turn the Dynex TV OFF.  (always OFF, ON)

 

Does anyone have a fix?  Or is this a problem with the Rogers controller?

 

 

 

 

Highlighted
Resident Expert
Resident Expert
Posts: 14,246

Re: Dynex TV and programming remote

Well yes/no a problem with the remote..

Could be the way the TV's codes are.

Some TVs, have an on/off code.. same code does both.

Some have an On and Off code seperate. (even though its the same button on the tv remote)

The rogers one, only works with an ON/OFF as the same code..
Could be something with that TV having the dual code..
OR

That say the LENGTH that its broadcasting the code, is too long, and the TV is picking it up as another ON signal.

I guess one thing you could try.. press it to turn stuff off, as soon as you see that it has turned it off, cover the sensor/transmitter at the front quickly.. and see if it still does it.